Rca D771 Bedienungsanleitung PDF herunterladen (Seite 4)

Using Automatic Code Search

The following instructions can be used to program the

remote to control the TV, VCR or DVD. If you want to

exit the automatic code search without programming any of

your components, press the CLEAR key until the LED (red

light) turns off.

1. Turn on the component you want to control (TV,

VCR or DVD).

2. Press and hold the component key you want to

program. While holding the component key, press

and hold ON•OFF until the LED on the remote

control turns on, then release both keys.

Note: The AUX1 and AUX2 keys can only be programmed

using Direct Entry Mode.

3. Point the remote at the component, press and release

PLAY, then wait five seconds or until the LED stops

flashing.

At this point the remote control is searching for the

correct code to program. If, after five seconds, the

component you want to control does not turn off,

press and release PLAY again to tell the remote to

search the next set of codes.

Continue pressing and releasing

PLAY until the

component turns off or you have searched through

all of the codes. There are 20 sets of codes. If the

component does not turn off after pressing PLAY 20

times, then the remote cannot control that particular

component.

If the component you want to control does turn off:

1. Press and release

REVERSE, then wait two seconds.

Repeat this step until the component turns back on.

2. To finish, press and hold

STOP until the LED on the

remote control turns off.

Using the Remote to Control a

Component

Because this universal remote can control several different

components (TV, VCR, DVD, etc.), it uses operational

modes triggered by the component keys. For example, if

you want the remote to control the TV, you would press the

TV key to put the remote into TV Mode. Then, if you want

to play a videotape, press VCR then PLAY (pointing the

remote at the VCR).

Changing the RF Remote Code

Your remote control is equipped with RF functionality.

This means that the remote can control the digital satellite

receiver using both IR (infrared) signals and RF (radio

frequency) signals if it is equipped with an RF receiver. IR

signals require line-of-sight to the receiver’s front panel

remote sensor. RF signals can control the receiver from

other parts of your house, even through walls. Installing

your RF remote control antenna will increase the range

of your RF remote signal. See the owner’s manual of your

DBS system for more details.

Note: This feature is only applicable for RCA DIRECTV digital

satellite receivers.

If you are experiencing interference from other RF

components, you may need to change the RF remote

control code. To change the code first in your satellite

receiver, do the following:

1. Select

Options in the Main menu.

2. Select

System Options.

3. Select

RF Remote.

4. If you normally use the

SAT key on your remote

to control your RCA satellite receiver, choose a

number between 000 and 255. Follow the on-screen

instructions to enter this number as your RF remote

control code. However, if you use the AUX1 or AUX2

key, choose a number between 000 and 099.

Then, to change the code on your remote to match

the satellite receiver, perform the following:

1. Press and hold the

SAT key, AUX1, or AUX2 key

(depending on which key you use to control your

satellite receiver).

2. Then use the Digit keys to enter the same RF remote

control code (000-255 for SAT), or (000-099 for AUX1

or AUX2) on your remote control.

Menu Function

The Menu function is used to make changes in the

selected settings, such as setting color, channels, timer,

etc. The MENU key displays TV, DVD player, and DBS

menu screens on your TV. Each Menu function will

vary from brand to brand.

Entering the Menu Mode

1. Push the component key on

the remote for the desired

menu screen.

2. Push the MENU key. This

allows you to view the menu

of the chosen component. The

menu should now be visible

on your television.

(BLINK)

Note: With some brands you may have to press the

GUIDE or INFO key for the on-screen menu.

1 2 3 4 5 6

Kommentare zu diesen Handbüchern

Keine Kommentare

Rca D771 Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fernbedienung Rca D771